Join us for Smart Buildings Exchange, Aug 15-17, 2023!

Smart Buildings Center

Energy Efficiency Innovation Center, Tool Library & Data Visualization

  • About
    • Staff
    • Board of Directors
    • Contact
    • Donate
  • Partners
    • Partner Benefits
  • Tool Library
    • Browse Inventory
    • Lending Library Policy
    • Customer Agreement
    • Tool Resources
  • Use Our Space
    • Training/Event Space
    • Large Conference Room
  • Training
    • Building Operator Certification
    • Remote Learning Calendar
      • Submit Event
    • Remote Learning Library
    • Washington State Controls Specialist Apprenticeship
  • Resources
    • Clean Buildings Performance Standard Helpdesk
    • Benchmark Support Services
    • K12 Ventilation and Indoor Air Quality Helpdesk
  • Events
    • SBX Conference
  • Blog

Is your Enthalpy-based Economizer Functioning Properly?

August 8, 2016 By Vamsi

handheld humidity controller
Vaisala Handheld Humidity and Temperature Meter

We loan a lot of tools out at the Smart Buildings Center’s Tool Lending Library. Often when the tools come back, they return with a story of success. Recently Jessica Sanborn with Elemental Commissioning borrowed a Vaisala HM 70 Handheld Humidity and Temperature Meter to tune an Enthalpy-based Economizer Controller on an Air-Handling Unit (AHU). Many of you are familiar how Enthalpy-based Economizers work, but for those of you who don’t know and haven’t yet fallen asleep, let us take a minute to explain how these work:

Buildings can generate a lot of heat. The people inside, running of lights, operation of copy machines and computers, and industrial equipment can all generate heat inside of a building and that’s why we need cooling. When cooling a building, there is typically a compressor at work. This could be in an application like a simple air conditioner all the way up to a large and complicated chiller plant. Running these compressors can use a lot of energy and one way of being more energy efficient is to try to minimize the amount of the time the compressor has to run. This can be done with an economizer.

The way an economizer works is whenever the cooling system is trying to cool the building, and the air outside of the building is cooler than the air inside of the building, the economizer system can shut off the compressor and use the cool outside air to cool the building. The only issue with this when the outside air is cool and humid, bringing that outside air into a warm building can make the occupants feel clammy. The solution to this is to incorporate outside air humidity in the equation as to whether to bring outside air in or to utilize the compressor to cool the building. An Enthalpy-based Economizer Controller will make sure that both the air and the humidity outside are low enough to comfortably cool a building.

Roof top air conditioner
A typical roof top Air-Handling Unit.

Now that we have some background, let’s revisit Jessica’s project! Tuning the accuracy of an Enthalpy-based Economizer Controller on an AHU especially near the humid shores of the Puget Sound requires an accurate measurement of temperature and humidity. This can be done with a tool like the Vaisala HM 70. As is often the case, the Building Automation System (BAS) sensor locations were not ideal due to structural and space limitations. Making slight adjustments to the BAS inputs based on the more accurate readings of the actual ambient enthalpy resulted in an increased range of economizer use and a reduction in the controller cycling on and off continuously (which could lead to premature failure). The end results were a considerable energy savings!

Jessica had some choice words to share about her experience with the tool:

If the Vaisala HM70 had not been used to make these slight adjustments, the system still would have satisfied the needs of the space, but the AHU would not have been optimized for energy savings and the humidity.” She also noted, “Having access to this high-end tool has allowed us to commission the system to a higher standard. Thank you Smart Buildings Center!”

The Smart Buildings Center’s Tool Lending Library has over 85 different building diagnostic tools and meters available for loan, come borrow a tool from us and create your next efficency success story.

Filed Under: Tool Library

Help fund our Education Program

DONATE TODAY

Sign up for updates

Join the Smart Buildings Center mailing list for information about events and smart buildings news.

Your email has been added to the Smart Buildings Center mailing list for information about events and smart building news.

News & Articles

Puget Sound Energy’s 2023 Accelerator program is open for business

March 17, 2023

Register for Certified Energy Manager Training at SBC, May 1st-5th

March 17, 2023

Register for Mar 23 11-12, Clean Buildings General Question and Answer Session

March 14, 2023

Estimating Your Building’s Emissions and Draft Targets for Proposed Seattle BEPS, Thursday Mar 23 12-1

March 14, 2023

2023 Built Environment Workforce Survey

February 23, 2023

CONTACT US
info@smartbuildingscenter.org
206-538-0832

Smart Buildings Center is a project collaboration with Northwest Energy Efficiency Council

NEEC logo
           

Smart Buildings Center · Pacific Tower, 1200 12th Ave. S., Suite 110, Seattle, WA 98144 · 206-538-0832

© 2023 · Northwest Energy Efficiency Council